HOME

JamesOS-K · Quick start

Make your first beat.

Three synth tracks, four drum lanes, 37 velocity keys, 16 pads and four faders. Use this guide to make your first beat on the SMK-37 Pro.

1. Install JamesOS-K

JamesOS-K can be installed on an SMK-37 Pro running M-VAVE firmware V15 or V16, or an earlier JamesOS-K build. Once JamesOS-K is installed, this installer can only update it to another JamesOS-K build. It cannot yet put M-VAVE firmware or another firmware back on the SMK-37 Pro. If you have a way to back up the unit's flash, do it before the first installation. The Editor does not support the SMK-37 Pro yet, so it cannot back up your projects. The installer does not create a backup.

  1. On a desktop computer, open Chrome or Edge and visit the JamesOS installer.
  2. Connect the powered-on SMK-37 Pro directly to the computer with a USB data cable. Close other music software using the SMK-37 Pro and stop playback.
  3. Open the installer, allow MIDI access, and follow the on-screen connection, review and installation steps. The installer identifies the connected instrument and checks that its firmware package matches its model. Keep the SMK-37 Pro connected and the browser open until the instrument restarts and the installer confirms it.

Installing unofficial firmware may void your warranty. An interrupted installation can leave the instrument unresponsive. See backups and recovery.

2. Make a sound

Connect headphones or speakers, switch on your SMK-37 Pro and raise K8, the master volume, gradually.

  • The screen opens on HOME. Play the keybed. OCT− and OCT+ move the octave.
  • Turn K1 and K2 (TIMBRE, HARMONICS) and listen to how they change the tone of played notes.
  • Turn K7 (PRESETS) to change the synth engine.
  • Press PATCH, turn K1 (or K5, SELECT) to browse 128 starting sounds (audition them with the keybed), then press PATCH again to select and keep one. KNOB BANK returns to HOME from any page.
  • Press ◄ or ►, or turn K6, to switch tracks. T1, T2 and T3 are synth tracks; DK is the drum kit.

3. Make a beat

  • Select the drum kit DK. Press SEQ: the 16 pads become the step grid. Turn K5 (SELECT) to choose drum lane D1, then tap pads to add or remove hits. Choose D2 to D4 to add other drum sounds.
  • Press SEQ PLAY. To set the tempo, press OCT− + GLOBE to open TEMPO and turn K1 (BPM).
  • Select a synth track and press SEQ. Play a key to choose a pitch, then tap pads to add steps. Hold a pad for a moment to set its note, length, velocity and condition.

4. Mix and master

  • Press FX. The first screen is the send levels for DRIVE, DELAY, MODULATION, REVERB. Turn the four knobs to adjust the sends.
  • Press FX again for the effect settings.
  • Reverb is shared by all tracks (the GLOBAL tag); the rest belong to the track (the TRACK tag).
  • FADER BANK opens MIXER: the four faders set the levels of T1, T2, T3 and DK. OCT− mutes and OCT+ solos the selected track. Tap FADER BANK again for KIT LEVEL, where the faders set drum lanes D1 to D4.
  • GLOBE cycles the master screens: PAN, FILTER, HEAT, COMPRESSOR and COMP TIME.
  • On DK, tap NOTE REPEAT for RETRIGGER: hold a lit pad to set extra hits and spacing with K1 and K2.
  • Stop playback, then press BT to open the SAVE menu. BT again quick-saves the current project. If there is no current slot, choose a slot and name first. Always save before switching off.

5. Handy gestures

Do thisTo get
Hold PATCH for 0.8 sNotes keep sounding after you let go (HOLD)
Hold ARP for 0.8 s on a synth trackArpeggiator on or off
Hold GLOBE, turn K5Jump to the master filter page
Turn K5 outside a browser, drum grid or menuSweep the master filter
On FX SENDS, hold OCT− and turn a knobSnap the send to 0%, 50% or 100%
Strike a pad on a page where the keys play notesPunch-in effect: LOOP, ECHO, FILTER or TREM
Hold NOTE REPEAT on a synth trackPUNCH FX settings
Hold SEQ, turn K1Pattern length
Hold NOTE REPEAT + SCALE for 0.8 sFader link on or off

The screen shows a hint while you hold a gesture button. Turn MONITOR on in TEMPO to see audio CPU load on the bottom two pixel rows.

Full manual

JamesOS-K is free community firmware for the M-VAVE SMK-37 Pro keyboard. It has three synth tracks, a four-lane drum kit, track effects, a shared reverb and a sequencer. It is built from the same source as JamesOS for the FM-1, so the sounds, engines, effects, sequencer, arranger and projects work in the same way. This manual describes the SMK-37 Pro panel. Start with the quick start for a first beat, or check the backup and recovery notes.

Warranty and risk. Installing unofficial firmware may void your hardware warranty. An interrupted update can leave the instrument unresponsive. JamesOS-K comes with no warranty (GNU GPL v3, sections 15 and 16). Back up your work before updating. JamesOS-K is not made or endorsed by the manufacturer of the SMK-37 Pro.

1. The instrument at a glance

2. Controls

Buttons

Press a page button once to open its first screen. Press it again to move to the next screen in that group. The names below are the ones printed on the SMK-37 Pro. Cues on the screen write SEQ PLAY as PLAY and SEQ REC as REC.

ButtonWhat it does
KNOB BANKReturns to HOME from any page or menu. On HOME it switches between the sound controls and the track filter. OCT− + KNOB BANK opens or leaves MOD DEPTHS and VOICE.
PARAAMP envelope, FILTER envelope, then envelope SETUP.
FXSENDS, DRIVE, DELAY, MODULATION, then REVERB.
GLOBECycles PAN, FILTER, HEAT, COMPRESSOR and COMP TIME. The mixers are not in this ring; FADER BANK opens them. Press OCT− + GLOBE for TEMPO and the USB MIDI settings. Hold and turn K5 for the master filter shortcut.
SCALECycle through LFO 1, LFO 2 and GLOBAL LFO. Hold NOTE REPEAT + SCALE for 0.8 seconds to switch the fader link.
CHORDCycle through PATCH 1 and PATCH 2. KIT LEVEL is not here; FADER BANK opens it.
PATCHBrowse SOUNDS or DRUM KITS. Tap again to keep the highlighted entry. Hold for 0.8 seconds to toggle HOLD: after 0.4 seconds the screen shows HOLD 0.8S: HOLD ON or HOLD OFF. The PATCH light blinks while HOLD is on.
ARPSynth arpeggiator. On synth tracks, hold for 0.8 seconds to toggle the arpeggiator. On DK, it shows the cue SWITCH TO T1 T2 T3 and does not open RETRIGGER.
NOTE REPEATOn DK, a tap opens RETRIGGER and another tap goes back. On a synth track, hold it as the punch shift key to open PUNCH FX. See NOTE REPEAT.
FADER BANKSwitch the faders between the track bank and the drum-lane bank, and open that bank's page: MIXER or KIT LEVEL.
SEQStep grid, then sequencer settings. Hold and turn K1 to change pattern length. OCT− + SEQ opens PATTERNS.
SEQ PLAYStart or stop the sequencer. With a step held, paste. On HOME, hold OCT− and press SEQ PLAY to switch polyphony.
SEQ RECArm or disarm recording. With a step held, copy.
BTOpen the SAVE menu. Follow the actions shown in its bottom bar.
OCT−Lower the synth octave. OCT− often acts as a Function key when held with another control; see the page-specific actions below.
OCT+Raise the synth octave, or perform the page-specific actions below.
◄ and ►Select the previous or next track, including from the PATCH and kit pages. They are ignored while a step is held.

Encoders

K1 to K4 match the four control columns. The active knob badge is highlighted; a dotted icon with an X means there is no parameter for that knob on this page. Turn faster to move more quickly through continuous values. Discrete choices such as engine or note selections keep their individual steps.

K5 (SELECT) normally sweeps the master filter. In SOUNDS or DRUM KITS it scrolls; on the drum step grid and RETRIGGER it selects a lane. SAVE screens use it for their own selection. These page-specific functions take priority over the filter shortcut.

K6 selects T1, T2, T3 or DK, like ◄ and ►. On KIT LEVEL it is inactive; press a page button before changing track with it.

K7 (PRESETS) selects a synth engine without changing its other sound settings. On drum HOME it chooses the kit engine; on the drum sequencer, KIT LEVEL and RETRIGGER it chooses the selected lane's voice. In SOUNDS or DRUM KITS it scrolls the browser.

K8 is the master volume.

Keybed and octave buttons

The 37 keys play the selected synth on HOME and parameter pages, and respond to how hard you strike them. The octave buttons shift synth notes by up to two octaves, and their lights show the current octave. The five lowest and five highest keys play notes too. Drum sounds have no octave shift. On SEQ, the keys set pitch and the pads become the step grid. RETRIGGER and KIT LEVEL have their own input rules.

WhereOCT− / OCT+
MIXERToggle mute / solo for the selected track.
KIT LEVELToggle mute / solo for the selected drum lane.
SEQ grid or RETRIGGERPrevious / next bank of 16 steps.
While editing a SEQ stepNudge its timing earlier / later, in 1/128-note increments.
SEQ settingsNo action.
PUNCH FXPrevious / next settings page.
SOUNDS browser on a synth trackChange the audition octave.
SAVE screensUse the BT and SEQ PLAY actions shown on screen.

Wheels and pedal

The pitch bend wheel moves the pitch of the selected synth track by up to two semitones. The mod wheel raises TIMBRE of the selected synth track toward its maximum. The pedal sustains notes played on the keybed. Pitch bend, the mod wheel and the pedal are also sent as MIDI when the track's MIDI channel is on. See the MIDI chart.

Reading the screen

Track colours identify the selected track. Goldenrod identifies global controls, including shared reverb and Punch FX. A TRACK badge means the effect settings belong to the selected track. A GLOBAL badge means the effect is shared, though its send can still be per track.

The header shows the track or globe badge, page title, tempo and battery. The battery shows four levels. The metronome swings once across per beat and centres while stopped. Small dots above the bottom cue bar show your position in a page group. Rounded button cues explain shortcuts; brief status messages temporarily replace them.

SCREEN GUIDE

Reading the screen graphics

These examples come from the firmware. Shapes, levels and colours respond to the current sound and settings; the labels and values on the screen identify the control.

TIMBRE
HARMONICS
MORPH
OSC MIX
LFO WAVE
LFO RATE
OCTAVES
ARP GATE

3. Pages

The screenshots and control graphics show examples of the screens. Values, track colours and graphics respond as you play and turn the controls.

HOME and kits · PARA · FX · GLOBE · MIXER and KIT LEVEL · SEQ · ARP · RETRIGGER · PATCH · SCALE · CHORD · Modulation · PUNCH FX

HOME (KNOB BANK)

HOME with the Analog VCF engine and its four controls
HOME with the Analog VCF engine and its four controls

On a synth track, HOME shows TIMBRE, HARMONICS, MORPH and OSC MIX. The first three shape the selected engine. OSC MIX blends its MAIN and AUX outputs; their sounds depend on the engine. Turn K7 (PRESETS) to choose a different engine.

Press OCT− + KNOB BANK to open the deep menu. Press KNOB BANK to move to its second page, and again to return to HOME. OCT− + KNOB BANK also returns to the sound pages.

HOME MOD DEPTHS with timbre, harmonics, morph and pitch modulation controls
HOME / MOD DEPTHS

MOD DEPTHS adjusts the combined modulation reaching TIMBRE, HARMONICS, MORPH and PITCH. Zero leaves the routed modulation unchanged. Positive values increase its depth; negative values reduce it.

HOME VOICE page with portamento, glide mode and amp mode
HOME / VOICE

On a synth track, PORTA TIME sets portamento from 0% to 100%, up to two seconds per octave. GLIDE MODE selects OFF, LEGATO (glide when notes overlap), or ALWAYS (glide from the previous pitch). AMP MODE selects the normal ENVELOPE or LPG, which couples a low-pass gate to the amplitude envelope. In LPG mode, GATE LENGTH limits how long a held note plays, from 10 ms to 2 seconds; OFF follows the key hold, and releasing a key early closes the gate. LPG uses a fixed 2 ms close; the amp RELEASE control is hidden in LPG mode. These controls are inactive on the drum kit.

On DK, turn K7 on HOME to choose BRAIDS or PLAITS. Use PATCH to browse the starting kits, including 80S and 90S:

KitK1K2K3K4
BRAIDS KITTIMBRECOLORSNAPGATE
PLAITS KITTIMBREHARMONICSMORPHGATE

The 80S and 90S starting kits use the PLAITS engine, so their HOME controls are TIMBRE, HARMONICS, MORPH and GATE. SNAP adjusts the attack character of the BRAIDS kit. GATE limits each hit's duration; OPEN lets its natural tail play. A shorter held-step LENGTH takes precedence. GATE is temporary and returns to OPEN when a session loads.

Press KNOB BANK again for the track filter: FILTER, RESONANCE, ENV DEPTH, KEY TRACK. FILTER spans low-pass through open to high-pass. ENV DEPTH is bipolar: it sets how much the filter envelope moves the filter. KEY TRACK switches note-based cutoff tracking on or off. The track filter and master filter are separate stages. On the track filter page, make a fresh OCT− hold and turn K1 to snap toward the low-pass end, open midpoint or high-pass end. Keep holding OCT− and turn again to move between those points.

Track filter controls and the OCT− plus K1 snap cue
Track filter

PARA (envelopes)

ENV / AMP with its envelope curve and ADSR settings
ENV / AMP with its envelope curve and ADSR settings

Three screens:

ScreenControls
ENV / AMPATTACK, DECAY, SUSTAIN, RELEASE of the sound's volume.
ENV / FILTERATTACK, DECAY, SUSTAIN, RELEASE of the modulation envelope.
ENV / SETUPINTENSITY, TARGET, LOOP, RETRIGGER for that modulation envelope.

HOME filter ENV DEPTH adds a separate amount of the modulation envelope to the filter. The envelope SETUP target and intensity can also route that envelope to a destination. See modulation for the interaction with the patch routes.

FX

FX SENDS with different effect send levels
FX SENDS with different effect send levels

The drum track and all three synth tracks have these five screens:

ScreenControls
SENDSDRIVE, DELAY, MODULATION, REVERB levels for the selected track.
DRIVEMODE (OVERDRIVE, DISTORT or FUZZ), GAIN, TONE, BIAS.
DELAYENGINE (DIGITAL, TAPE ECHO, MULTITAP or GLITCH), TIME, FEEDBACK, TONE.
MODULATIONENGINE (CHORUS, FLANGE, PHASER or VIBRATO), RATE, DEPTH, FEEDBACK.
REVERBENGINE (ROOM, HALL or SPACE), SIZE, DECAY, PRE DELAY.
FX DELAY with engine, time, feedback and tone
FX DELAY

Use SENDS to set how much of each effect the selected track receives.

FX DRIVE with mode, gain, tone and bias
FX DRIVE

On DRIVE, GAIN sets the strength of the distortion, TONE adjusts its brightness, and BIAS changes its character by offsetting the distortion. At zero bias each drive mode uses its natural character; higher settings add asymmetry.

On DELAY, TIME selects a tempo-synchronised note division, FEEDBACK controls the repeats, and TONE darkens or brightens them. T means triplet (two-thirds of the named note); D means dotted (one and a half times the named note). At 120 BPM, 1/4 is 500 ms, 1/4T is about 333 ms and 1/4D is 750 ms.

FX MODULATION with engine, rate, depth and feedback
FX MODULATION

On MODULATION, RATE and DEPTH set the speed and amount of movement. FEEDBACK adds resonance and colour, especially with FLANGE and PHASER; zero leaves the effect uncoloured by feedback.

REVERB is shared by all tracks: its ENGINE, SIZE, DECAY and PRE DELAY affect the shared reverb, while each track's reverb SEND is set on the SENDS page. PRE DELAY sets when the reverb begins: AUTO derives it from the reverb settings, while 1/64T, 1/64, 1/32T, 1/64D, 1/32, 1/16T, 1/32D, 1/16, 1/8T, 1/16D and 1/8 follow the current tempo. The dry sound remains immediate. To hear the difference, use a short sound with ROOM and a high reverb SEND, set the tempo to 60 BPM, then compare 1/64T with 1/8. Allow a few seconds after changing the setting for the timing to settle.

FX REVERB with engine, size, decay and pre delay
FX REVERB

On SENDS, hold OCT− and turn any knob to jump directionally between 0%, 50% and 100%. The cue appears below the four send bars. A snap gesture does not change octave; a plain OCT− tap still lowers the synth octave. Without the modifier, sends adjust continuously.

GLOBE (global)

GLOBAL PAN with the four track pan controls
GLOBAL / PAN

Press GLOBE repeatedly to visit the master screens. Press OCT− + GLOBE to open TEMPO; press GLOBE there to reach the USB MIDI pages. From TEMPO or either USB MIDI page, OCT− + GLOBE returns to PAN. The mixers are not in this ring. They open from FADER BANK; see MIXER and KIT LEVEL.

ScreenControls and use
GLOBAL / PANPan for T1, T2, T3 and DK. The centre marker indicates true centre.
GLOBAL / FILTERFILTER, RESONANCE and ENV DEPTH. The fourth slot is inactive. K5 and K1 edit the same master filter.
GLOBAL / HEATHEAT TYPE (BITCRUSH, SATURATE or TAPE WOW), AMOUNT. This is separate from each track's DRIVE.
COMPRESSORSOURCE, THRESHOLD, RATIO, MAKEUP. SOURCE offers OFF, ALL, TRACK 1–3 or KICK DRUM.
COMP TIMEATTACK, HOLD, RELEASE, MIX.
TEMPO (OCT− + GLOBE)BPM, SWING, CLOCK SOURCE and MONITOR. The clock readout appears in the header, and the build number appears in the cue area.
USB MIDI 1 and USB MIDI 2Input channels for the synth tracks and the drum lanes. See routing and clock.

To jump to the master filter, hold GLOBE and turn K5. On GLOBAL / FILTER, make a fresh OCT− hold and turn K1 to snap toward the low-pass end, open midpoint or high-pass end. Keep holding OCT− and turn again to move between those points.

Global filter controls and the OCT− plus K1 snap cue
Global filter

BPM and SWING are shared. MONITOR is described in section 6.

Compressor

Compressor screen showing source, threshold, ratio, makeup and gain-reduction meter
COMPRESSOR with its gain-reduction meter and four controls
Compressor timing graph with attack, hold and release sections
COMP TIME: the selected timing section is highlighted

The global compressor controls the dynamics of the finished mix. Press GLOBE until you reach COMPRESSOR; press it again for COMP TIME. Both pages show a goldenrod gain-reduction meter above the controls: it shows how much the compressor is turning the signal down. On COMP TIME, the graph combines ATTACK, HOLD and RELEASE; turning a control highlights its section. MIX blends the compressed and uncompressed signals.

PageControlWhat it does
COMPRESSORSOURCEChooses the signal that triggers compression: OFF, ALL, TRACK 1–3 or KICK DRUM. Choose a track or kick to make that signal drive compression of the mix.
COMPRESSORTHRESHOLDSets the level above which the compressor begins reducing gain.
COMPRESSORRATIOSets how strongly signals above the threshold are compressed. 1:1 applies no compression.
COMPRESSORMAKEUPAdds gain to the compressed signal.
COMP TIMEATTACKSets how quickly compression responds to a rising signal.
COMP TIMEHOLDSets how long compression holds before releasing.
COMP TIMERELEASESets how quickly compression eases after the signal falls.
COMP TIMEMIXBlends the compressed and uncompressed signals.

For a pumping effect, try KICK DRUM as the source and adjust THRESHOLD, RATIO and RELEASE while the beat plays. Use the meter and your ears to set the amount of gain reduction.

MIXER and KIT LEVEL (FADER BANK)

MIXER page opened by FADER BANK
MIXER, opened by FADER BANK

The four faders set levels. The track bank sets T1, T2, T3 and DK. The drum bank sets the four drum lanes, D1 to D4. The FADER BANK light is on in the drum bank.

Tap FADER BANK to switch banks. It also opens the real page for the bank you switched to: MIXER for the track bank, KIT LEVEL for the drum bank. The page stays until you press a page button. Tap FADER BANK again to switch to the other bank and its page.

On MIXER, K1 to K4 set the same track levels as the faders. Turning a level knob also selects that track, even when its level is already at a limit. OCT− mutes and OCT+ solos the selected track.

KIT LEVEL page opened by FADER BANK
KIT LEVEL, opened by FADER BANK

On KIT LEVEL, each fader or knob controls D1 to D4, and each knob selects that lane. K7 changes its voice. OCT− toggles mute; OCT+ toggles solo. The four strips show matching D1 to D4 badges, short voice names and M/S indicators. Keybed keys and K6 are inactive here. Use the track's PATCH pages under CHORD, and the kit's PARA and SCALE pages for modulation.

Several drum lanes can be soloed together. Solo excludes only the other drum lanes, so synth tracks keep playing. Mute takes precedence over solo. The underlying lane levels are preserved; existing effect tails may continue to decay. Lane mutes save with the project; solos clear on load.

The MIXER meter shows each track after its track effects and pan, before shared reverb, master compression and master output. Its top turns red at full scale and it decays after a peak. KIT LEVEL meters show individual lanes before the kit's shared track-effects chain, so the MIXER DK meter shows the summed kit after that chain. Lane names use a five-character maximum, including KICK1, SNARE, OHAT, CHAT, CYMB and TOM.

Moving a fader on any other page shows the mixer of the current bank for 1.6 seconds. The view restarts while the fader keeps moving. On MIXER or KIT LEVEL, moving a fader just updates the page.

Faders use pickup. A fader changes a level only after it has crossed the stored value, so switching banks or loading a project never makes a level jump. While a step is held, FADER BANK opens no page and shows only TRACK FADERS or DRUM FADERS.

MIXER with the fader link on, showing the T1+T2 cue
Fader link on, track bank: T1+T2

The fader link lets fader 1 set two levels at once. In the track bank it sets T1 and T2. In the drum bank it sets kit lanes D1 and D2. With the link on, fader 2 is ignored in both banks. The mixer cue shows T1+T2 and the KIT LEVEL cue shows D1+D2.

KIT LEVEL with the fader link on, showing the D1+D2 cue
Fader link on, drum bank: D1+D2

To switch the fader link, hold NOTE REPEAT and SCALE together for 0.8 seconds. The screen shows FADER LINK ON or FADER LINK OFF. Switching it on copies the T1 level to T2 and the level of drum lane 1 to lane 2 at once. If you let go of either button early, SCALE acts as a normal tap and nothing is switched. The setting is saved with the project.

SEQ: patterns and step editing

Synth sequencer with notes on the 16-step grid and the KEYS SET PITCH, PADS SET STEPS hint
Synth sequencer with notes on the step grid

Press SEQ for the current track's grid. The step grid is drawn as two rows of eight, to match the 16 pads. The screen shows the hint KEYS SET PITCH, PADS SET STEPS. The pads switch the 16 steps of the current bank on and off; OCT− and OCT+ move between four banks, for up to 64 steps.

On patterns longer than 16 steps, the bottom cue alternates every 3 seconds between OCT−/+ + REC SHIFT NOTES and OCT−/+ STEP BANK.

Sequencer with a 32-step pattern and the OCT−/+ STEP BANK cue
A 32-step pattern with the STEP BANK cue

On a synth track, the keybed keys set pitch. Play a key to choose and hear the pitch that new steps will use, then tap pads to add steps. The five lowest and five highest keys work too; OCT− and OCT+ move their octave. On DK, turn K5 to choose D1 to D4, or press one of the first four BLACK KEYS. The pads toggle hits in that lane. K7 changes the selected lane's voice. Knob settings without a held step are defaults for new steps, rather than edits to every existing hit.

Drum sequencer with kick hits on the step grid and the other lanes listed below
Drum sequencer

Hold a pad to edit its step. On a synth track, play a key while you hold the pad to set the step's note to that key. The edit controls appear: NOTE, LENGTH, VELOCITY and CONDITION on K1 to K4. OCT− and OCT+ nudge its timing earlier or later in 1/128-note increments. The display simplifies the offset to a musical fraction, such as +1/32 or −3/64. The available range depends on the track speed and swing, keeping the note within its neighboring step boundaries. Holding SEQ with a step makes it a fill step. Conditions include ALWAYS, probabilities, FIRST PASS, REPEATS, AFTER HIT, AFTER MISS, NEIGHBOR, ALONE, FILL, NO FILL and A-of-B patterns.

A held step with its note, length, velocity and condition controls
A held step

To shift every note in the current track by one step, hold SEQ REC and press OCT− or OCT+. Keep holding SEQ REC to shift again. Notes that pass the first or last step wrap around the track's sequence. On DK, all four drum lanes move together; timing and other step settings move with each note.

To copy a step, hold an active pad and press SEQ REC. Hold a destination pad and press SEQ PLAY to paste. Synth steps paste to synth tracks and drum steps to drum lanes; the step's edits come with it. With no copied step, SEQ PLAY retains its transport function.

Press SEQ again for STEPS, SPEED, QUANTIZE. STEPS is the pattern length; SPEED selects 1/8, 1/16 or 1/32; QUANTIZE controls recording-time quantisation. Hold SEQ and turn K1 as a shortcut to pattern length. SEQ REC arms recording; SEQ PLAY starts or stops playback.

ARP: synth arpeggiator

ARP page with mode, rate, octaves and gate
ARP on a synth track

On T1 to T3, press ARP for MODE, RATE, OCTAVES, GATE. Hold ARP for 0.8 seconds to toggle the arpeggiator. While it is on, the ARP page shows an ARP: ON badge. HOLD (a 0.8 second hold of PATCH) and the pedal sustain notes after you release the keys.

MODE offers UP, DOWN, UP AND DOWN, RANDOM and MANUAL. MANUAL follows the order you played the notes. RATE offers 1/8, 1/8T, 1/16, 1/16T and 1/32. The 3 beside the note icon means a triplet; straight rates follow global swing. GATE sets each arpeggiated note's length as a fraction of the interval.

ARP page on the drum track showing the cue SWITCH TO T1 T2 T3
ARP on the drum track shows the cue SWITCH TO T1 T2 T3

The drum track has no arpeggiator. On DK, ARP opens a page titled ARP that shows one line, SWITCH TO and the badges T1, T2 and T3. The knobs do nothing there. A track arrow onto the drum track while the ARP page is open shows the same cue. Holding ARP for 0.8 seconds on DK just opens this page. To use the arpeggiator, select a synth track.

RETRIGGER: repeated drum hits

Drum retrigger grid with a held step and its retriggers and spacing
RETRIGGER with a held step

On DK, tap NOTE REPEAT to open RETRIGGER, with all four drum lanes visible. Tap NOTE REPEAT again to go back to the page you came from. Any page button, including ARP, or a track arrow also leaves RETRIGGER. Nothing happens while a step is held.

NOTE REPEAT

On a synth track, NOTE REPEAT does something else: hold it on a page where the keys play notes and it acts as the punch shift key. It opens the PUNCH FX page; see PUNCH FX. Together with SCALE it switches the fader link.

  1. Pick the drum lane. The first four BLACK KEYS choose D1, D2, D3 and D4, from left to right. You can also turn K5.
  2. If the pattern is longer than 16 steps, press OCT− or OCT+ to show the bank of steps you want.
  3. Hold a lit pad. An empty step does not audition or accept a retrigger edit.
  4. Turn K1, RETRIGS, for 0–7 extra hits. OFF means no repeats beyond the original hit.
  5. Turn K2, SPACING, for the interval between hits: 1/128, 1/64, 1/32, 1/16, 1/8, 1/4, 1/2 or 1/1 note.
  6. Release the pad to finish editing. Turning those knobs without holding a lit pad does not edit it.

A later hit in the same lane replaces any remaining repeats. The original hit's condition is checked once; repeats do not roll its probability again. Retriggers save with the project.

PATCH: SOUNDS and DRUM KITS

SOUNDS browser
SOUNDS browser

On a synth track, PATCH opens SOUNDS: 128 sounds, starting with 32 favorites and followed by categories for bass, leads, keys, pads and more. On DK it opens DRUM KITS: 12 starting points for BRAIDS and PLAITS, including 80S and 90S sounds.

DRUM KITS browser
DRUM KITS browser

Turn K1, K5 or K7 to browse the five visible rows. The highlighted entry is auditioned by the keys and by a running sequence. The knob chip lights in the track colour while you scroll. Press PATCH again when the cue reads LOAD PRESET to keep that entry. Leaving before keeping it restores the previous sound. The drum browser preserves the sequence, lane voice choices and levels.

SCALE: LFO

LFO controls
LFO controls

Two LFOs per track, each with WAVE, RATE, TARGET, DEPTH. WAVE offers SINE, TRIANGLE, SAW, SQUARE and SAMPLE HOLD. The target menu follows the selected engine; on a Plaits synth track, MODEL steps through the models around the current sound. DEPTH sets how far it moves. The display uses MORPH for the relevant Plaits control. Route badges show which LFO or patch is affecting a parameter, with colour and pulsing to distinguish them.

Press SCALE to cycle through LFO 1, LFO 2 and GLOBAL LFO. The global LFO is shared across the instrument; its targets include the global filter and resonance, heat, compressor controls, and reverb size and decay.

CHORD: patches

PATCH 1 controls for the selected track
PATCH 1 for the selected track

Press CHORD to cycle through PATCH 1 and PATCH 2. KIT LEVEL is not on this button; FADER BANK opens it. Each track has its own patches, including the drum kit. Each patch has SOURCE, TARGET, AMOUNT and ENABLE; negative amounts invert the route. On a synth track, its targets match the track LFO targets, including MODEL and the arpeggiator controls. In HOME's MOD DEPTHS page, scale modulation for TIMBRE, HARMONICS, MORPH and PITCH.

Modulation: how routes interact

The source labels describe these signals:

SourceMeaning
OSC AVG / MIX AVGSigned averages from the preceding audio block. They are not audio-rate oscillator or mix patch outputs.
AMP ENV / FILTER ENVThe amplitude or filter envelope.
LFO 1 / LFO 2The selected waveform of that LFO. Dedicated TRI and SQU sources provide its triangle or square signal.
GLOBAL LFOThe shared LFO waveform. PATCH AMOUNT sets its depth independently of the global LFO's own DEPTH setting.
VELOCITY / NOTEThe most recently played note's velocity or pitch.
RANDOMA new random signal each audio block.
RANDOM PER NOTEA new value on each note-on, held until the next. Polyphonic voices and drum lanes on the same track share the most recent value.
GATEHigh during the filter envelope's attack, decay and sustain stages.

Targets include pitch, the engine's sound controls, FILTER FREQUENCY, FILTER RESONANCE, TRACK LEVEL and TRACK PAN, the amp envelope, DRIVE SEND, DELAY SEND, MOD FX SEND, REVERB SEND and the LFO and arpeggiator controls. Choices depend on the engine. Kit modulation signals are shared by the kit, rather than independent per drum lane.

LFO and PATCH routes can contribute to the same destination. MOD DEPTHS scales the combined modulation applied to TIMBRE, HARMONICS, MORPH and PITCH. At 0% it passes unchanged; +50% makes it one and a half times as strong, −50% halves it, and −100% removes it. The sign of the underlying route is preserved.

A valid enabled patch route sourced from FILTER ENV replaces the envelope SETUP direct route, even when its amount is zero or its destination is different. ARP destinations do not replace that direct route. Disable that patch to restore the direct route. HOME filter ENV DEPTH remains an independent filter contribution. Track filter modulation can sweep through the open center between low-pass and high-pass.

PUNCH FX

PUNCH FX settings page with loop, echo time, filter and tremolo
PUNCH FX settings

On a page where the keys play notes, strike a pad to start a punch effect. Each row of four pads is, from left to right, LOOP, ECHO, FILTER and TREM, repeated across all four rows. One effect runs at a time while its pad is held; releasing the pad ends the effect. Only a pad struck in this mode counts, so holding a pad across a screen change does not start an effect. The step grid, RETRIGGER, PATTERNS and the SAVE screens keep their own pad roles. Punch effects act on the finished mix and use the global goldenrod colour. ECHO is unavailable while polyphonic voices use its delay memory; the screen shows ECHO UNAVAILABLE IN POLY.

On a synth track, hold NOTE REPEAT to show the PUNCH FX settings. Releasing it returns to the page you were using. The pads still start the effects while you hold it. On DK, NOTE REPEAT opens RETRIGGER instead, so select a synth track to edit the settings.

PadSetting on page oneSetting on page two
LOOPK1: loop length, 1 BAR, 1/2 BAR, 1/4 BAR or 1/8 BAR.None.
ECHOK2: echo time, 1/32, 1/16, 1/8 or DOT 1/8.K2: FEEDBACK.
FILTERK3: LOW PASS, HIGH PASS, LP SWEEP or HP SWEEP.K3: AMOUNT.
TREMK4: tremolo rate, 1/4, 1/8, 1/16 or 1/32.K4: DEPTH.

OCT− and OCT+ move between the two PUNCH FX settings pages. LOOP returns to the first page because it has no second-page control.

4. Gestures and shortcuts

GestureResult
Hold PATCH for 0.8 secondsToggle HOLD.
Hold ARP for 0.8 seconds on a synthToggle the arpeggiator.
Tap NOTE REPEAT on DKOpen RETRIGGER. Tap again to go back.
Hold NOTE REPEAT on a synthShow the PUNCH FX settings.
Hold NOTE REPEAT + SCALE for 0.8 secondsSwitch the fader link.
Tap FADER BANKSwitch the fader bank and open MIXER or KIT LEVEL.
Move a fader on another pageShow the mixer of the current bank for 1.6 seconds.
Hold GLOBE, turn K5Jump to the master filter and sweep it.
Fresh OCT− hold on GLOBAL / FILTER, turn K1Snap the filter to an end or the open midpoint.
Hold OCT−, turn a knob on FX SENDSSnap that send to 0%, 50% or 100%.
Hold SEQ, turn K1Change pattern length.
OCT− + GLOBEOpen TEMPO, or return from TEMPO or USB MIDI to PAN.
OCT− + SEQOpen PATTERNS, or return from PATTERNS or ARRANGE to SEQUENCER.
OCT− + KNOB BANKOpen or leave MOD DEPTHS and VOICE.
On HOME, hold OCT− and press SEQ PLAYSwitch polyphony, with playback stopped.
Hold an active SEQ pad + SEQ REC; hold a compatible destination pad + SEQ PLAYCopy and paste a step.
Hold a SEQ pad, turn knobsEdit that step's note, length, velocity and condition.
Hold a SEQ pad on a synth track, play a keySet that step's note to the key.
Hold a SEQ pad, press OCT− / OCT+Nudge its timing.
Hold SEQ with a stepMake it a fill step.
Hold a lit drum pad on RETRIGGEREdit RETRIGS and SPACING with K1 and K2.
Turn a mixer level knobAdjust its level and select its track or drum lane.
Strike a pad on a page where the keys play notesUse Punch FX: LOOP, ECHO, FILTER or TREM.
◄ or ►Select the previous or next track.

5. Saving and projects

Save and load

BT opens the SAVE menu: QUICKSAVE, SAVE AS, LOAD and INIT. Follow the bottom cues: BT confirms or quick-saves where offered; SEQ PLAY cancels. Quick-save writes the current slot. If no current slot is selected, choose a slot and name to save first. There are 12 slots and project names can contain up to 12 characters. K1 and K2 edit the name. Project-list selections use global goldenrod.

SAVE menu with quicksave, save as, load and init
The SAVE menu

Loading with unsaved changes opens SAVE FIRST?. INIT starts a blank project after confirmation. Stop playback before saving or initializing. These actions stop lingering notes and effect tails. If SEQ REC is armed, it pauses during the operation and is armed again afterward. Save before switching off.

Project storage

Projects contain the session and pattern bank. Retriggers, lane mutes and the fader link setting save with the project; lane solos clear on load. Drum GATE is temporary and returns to OPEN when a session loads.

Project compatibility. If a project cannot be loaded, keep a backup and do not overwrite a slot whose contents you need.

Backups and recovery

The Editor does not support the SMK-37 Pro yet. It cannot download or restore projects from this instrument. Save your current edits on the instrument before changing firmware, and back up the unit's flash before the first installation if you have a way to. Changing firmware can erase saved data. JamesOS-K can be installed on an SMK-37 Pro running M-VAVE firmware V15 or V16, or an earlier JamesOS-K build. Once JamesOS-K is installed, this installer can only update it to another JamesOS-K build. It cannot yet put M-VAVE firmware or another firmware back on the SMK-37 Pro. If an installation stops, check that the SMK-37 Pro still starts normally before doing anything else.

Patterns and arrangement

Each project stores up to eleven patterns, subject to available project storage. Press OCT− + SEQ to open PATTERNS; from PATTERNS or ARRANGE, press it again to return to SEQUENCER. The first eleven pads select patterns; during playback a selection queues for the next bar. To create a repeating chain, hold the first pattern pad, tap each following pattern pad in order, then release the first pad. Tap a pattern again to repeat it in the chain. A single pattern press ends the chain. Hold a source pattern pad and press SEQ REC to copy, then hold a destination pad and press SEQ PLAY to paste.

Patterns page showing the eleven pattern pads and the active pattern
PATTERNS

On PATTERNS, turn K4 from PATTERN to ARRANGE to open ARRANGER; stop playback before changing modes. Turn K1 to move the cursor between blocks and gaps. Press a pad on a block to change its pattern, or at a gap or END to insert a block. K2 sets the selected block's length, or the length of the next block when the cursor is at a gap or END. K3 switches whole-arrangement LOOP MODE on or off. Hold OCT− and press SEQ REC to remove the selected block. SEQ PLAY starts at the cursor, or at the beginning when the cursor is at END. Turn K4 back to PATTERN to select or queue patterns with the pads.

Arranger page with pattern blocks on a song timeline
ARRANGER

An arrangement can contain up to 64 blocks, with 1–16 bars per block. Save the project to keep its pattern bank and arrangement.

Editor: project transfer

The JamesOS Editor moves saved projects between a compatible FM-1 and a computer. It does not support the SMK-37 Pro yet.

Polyphony

With the sequencer stopped, select a synth on the first HOME page, hold OCT− and press SEQ PLAY to toggle polyphony. The cue on the screen reads OCT- + PLAY. The HOME badge shows MONO or POLY and the available voice count. The selected synth can play chords; the number of simultaneous voices depends on the sound engine and modulation settings, up to eight. The other synth tracks and drums are unavailable while the voices are in use; their settings and sequences are retained. Starting playback restores the normal track engines; HOME shows “POLYPHONY OFF DURING PLAYBACK” while the sequencer runs. Some polyphonic configurations use delay memory for additional voices; punch echo is unavailable while that memory is in use. When playback stops, the return to polyphony waits until held synth notes and the selected track's audible release finish.

6. The CPU monitor

TEMPO with MONITOR available on the fourth knob
TEMPO with the MONITOR control

Press OCT− + GLOBE to open TEMPO and turn K4, MONITOR, to ON. It uses the same ON/OFF toggle style as other settings. Its setting is saved with the project.

If two or more audio overruns occur within four bars, the instrument enables MONITOR and shows CPU USAGE HIGH. MONITOR ENABLED. once per power-on session.

The bottom two pixel rows show the average audio load, with a marker for the maximum. The meter turns red after an overrun. The MONITOR card shows AVG, MAX and OVR.

This is an average, not a guarantee against a slow individual block. If you hear clicks and the meter is near the limit, reduce effect sends or simplify the sound. MIXER and KIT LEVEL show signal level; this bottom bar shows processor load.

7. MIDI and USB audio

JamesOS-K has no DIN MIDI port. MIDI is USB only. MIDI input channels can be assigned to T1 to T3 and drum lanes D1 to D4. Program Change chooses an engine or kit; CC 7 controls synth track or drum-lane level, CC 71 controls COLOR/MORPH and CC 74 controls TIMBRE. MIDI Start, Continue and Stop control the sequencer, and USB MIDI clock can be selected as the timing source. The keybed, wheels and pedal send MIDI too. See the MIDI chart.

USB audio output is stereo, 16-bit. The sound engine runs at 44.1 kHz and the USB audio device presents 48 kHz to the computer.

8. Specifications and limits

ItemLimit
Tracks3 synth tracks and 1 drum track with 4 lanes.
Synth engines24 Plaits engines.
Kit enginesBRAIDS and PLAITS. The 80S and 90S starting kits use PLAITS.
Starting sounds128 synth sounds and 12 drum-kit starting points.
Keybed37 keys with velocity. Octave shift of up to two octaves.
Pads16 RGB pads: steps, pattern selection and four punch effects.
Faders4 faders in two banks: T1, T2, T3 and DK, or drum lanes D1 to D4.
Encoders8: K1 to K4 knobs, K5 SELECT, K6 track, K7 PRESETS, K8 master volume.
Wheels and pedalPitch bend (two semitones), mod wheel and a pedal input.
SequencerUp to 64 steps per track, in four banks of 16.
Tempo60–240 BPM.
RetriggersUp to 7 extra hits per drum step.
PolyphonyUp to 8 voices on the selected synth track, depending on the engine.
Projects12 slots; names up to 12 characters; each project contains a pattern bank.
Modulation2 LFOs and 2 PATCH slots per track, plus 1 global LFO. Modulation is evaluated at block rate.
ReverbOne shared tank; per-track sends.
MIDIUSB only. No DIN MIDI.
Audio44.1 kHz internally; stereo 16-bit USB audio at 48 kHz.
Processing256-frame audio blocks; heavy projects can approach the real-time deadline.

9. Troubleshooting

ProblemWhat to check
No sound from a trackIts level on MIXER, mute and solo states, the master volume on K8, plus the volume of your speakers or headphones.
A fader does nothingFaders use pickup: move the fader past the stored level first. Check which bank is active; the FADER BANK light is on in the drum bank.
One fader moves two levels and fader 2 does nothingThe fader link is on. Hold NOTE REPEAT and SCALE for 0.8 seconds to switch it off.
Notes keep sounding after you let goHOLD is on (the PATCH light blinks) or the pedal is down. Hold PATCH for 0.8 seconds to switch HOLD off.
One drum lane is silentKIT LEVEL's lane level, M/S state, chosen voice, GATE and that step's length. A mute takes precedence over solo.
ARP shows SWITCH TO T1 T2 T3The drum track has no arpeggiator. Select a synth track. Tap NOTE REPEAT on the drum track for RETRIGGER.
The drum knobs do nothingOn RETRIGGER, hold a lit pad first. On HOME, the available knobs depend on whether BRAIDS or PLAITS is selected.
K6 does nothing on KIT LEVELPress a page button before changing track with it.
Pads do nothing on the drum gridOn SEQ, pads switch steps in the selected lane. Choose a lane with K5 first.
A filter-envelope route seems inactiveCheck whether an enabled PATCH using FILTER ENV has replaced the direct route.
Clicks or dropoutsEnable MONITOR and simplify effects or sound settings if load approaches the limit.
SAFE AUDIO: SAVE+RESTARTThe instrument has fallen back to one audio core. Save your work and restart; polyphony is unavailable in this state.
STORE FULLThe project cannot fit in the available storage. Reduce its contents, then try saving again.
A project fails to loadPreserve your work, note the firmware build number and report what happened.

MIDI implementation

JamesOS-K receives MIDI over USB. The SMK-37 Pro has no DIN MIDI. JamesOS-K also appears to the computer as a USB-MIDI and USB-audio device.

Routing and clock

Press OCT− + GLOBE to open TEMPO, and use K3 to select CLOCK SOURCE. Press GLOBE once for USB MIDI / 1, where K1 to K3 set the input channels for T1 to T3. Press GLOBE for USB MIDI / 2, where K1 to K4 assign D1 to D4. The defaults are channels 1–3 for T1 to T3 and 4–7 for D1 to D4. Each destination can use any channel 1–16, including a shared channel, or OFF to disable its MIDI input and keyboard MIDI output. Any note on a drum lane's assigned channel triggers that lane's selected voice. Channel 10 needs an explicit assignment. These settings are saved with the session.

USB MIDI 1 with the input channels of the three synth tracks
USB MIDI 1

With CLOCK SOURCE set to USB/MIDI, JamesOS-K follows clock and transport received over USB. Use one clock source at a time. It waits for a stable incoming MIDI clock and stops playback if clock is lost. Start begins at the beginning. Continue resumes the locally stopped position. Song Position Pointer (F2) stops synchronized playback and requires a new Start.

Messages received

MessageEffect
Note On (velocity above 0)Plays a note on the track; velocity sets level. While SEQ REC is armed it is recorded into the pattern.
Note Off, or Note On with velocity 0Releases the note.
Program ChangeLoads a sound onto the track (below). A number the track cannot take shows PRESET ROLE LOCKED.
CC 7Synth track level or assigned drum-lane level (0 to 127).
CC 71Track COLOR (0 to 127).
CC 74Track TIMBRE (0 to 127).
CC 120, CC 123All sound off or all notes off for that track.
Start (0xFA)Start the sequencer.
Continue (0xFB)Resume the locally stopped position.
Stop (0xFC)Stop the sequencer.
Clock (0xF8)Supply timing when USB/MIDI clock is selected.

Received pitch bend, aftertouch, modulation wheel, RPN/NRPN and bank select are not implemented. The pitch bend and mod wheels on the panel work on the selected synth track.

Program numbers

ProgramSoundTracks
52 to 75The 24 synth engines, in the order of the table belowSynth tracks 1 to 3
48BRAIDS KITDrum track
76PLAITS KITDrum track

Programs 0 to 47 and 49 to 51 are not selectable on these tracks. Select the 80S and 90S kits in DRUM KITS. The 128 bank sounds on the PATCH page are sets of settings, not program numbers.

ProgramEngineProgramEngineProgramEngine
52ANALOG VCF60VIRTUAL AN68SWARM
53PHASE DIST61WAVESHAPE69NOISE
54FM BASS62FM70PARTICLE
55FM KEYS63GRAIN71STRING
56FM PAD64HARMONIC72MODAL
57WAVE TERRAIN65WAVETABLE73KICK
58STRING MACH66CHORD74SNARE
59CHIPTUNE67SPEECH75HI HAT

Drum notes

Any note received on a drum lane's assigned MIDI channel plays that lane. Choose the lane's voice with K7 on the drum sequencer, KIT LEVEL or RETRIGGER. If multiple lanes share a channel, a note triggers each assigned lane.

Messages sent

When you play the keybed, JamesOS-K sends Note On, with the velocity you play, and Note Off on the track's channel, so a DAW or other synth can follow what you play. Keybed output uses USB MIDI channels 1–3 for synth tracks and channel 4 for drums. Channel assignments do not change these output channels, but setting a track or drum lane to OFF suppresses its keyboard MIDI output.

For the selected synth track, JamesOS-K also sends the pitch bend wheel as Pitch Bend, the mod wheel as CC 1 and the pedal as CC 64, on the same channel as that track's notes. A track set to OFF sends none of these. It does not send clock, Program Change or other CC messages.

System exclusive

USB SysEx is used by the installer and diagnostic tools. JamesOS-K also supports the community screen-reader protocol over USB MIDI: a compatible screen reader can announce the current screen, controls and status messages. The device stays silent until a reader connects. To use it, connect the instrument by USB, open the FM-1 Screen Reader page in Chrome or Edge and choose Connect. Avoid sending unrelated SysEx during an update.

Audio

USB audio output, stereo, 16-bit. The instrument renders at 44.1 kHz; the computer sees a 48 kHz device.